ARM® Versatile™ Express Juno r2 Development Platform (V2M-Juno r2) Technical Reference Manual


Table of Contents

Preface
About this book
Product revision status
Intended audience
Using this book
Additional reading
Feedback
Feedback on this product
Feedback on content
1 Introduction
1.1 Precautions
1.1.1 Ensuring safety
1.1.2 Preventing damage
1.2 About the Versatile™ Express Juno r2 Development Platform
1.3 Location of components on the V2M‑Juno r2 motherboard
1.4 Connectors on front and rear panels
2 Hardware Description
2.1 Overview of V2M‑Juno r2 motherboard hardware
2.2 Juno r2 ARM Development Platform SoC
2.3 External power
2.4 Power management and temperature protection
2.4.1 Power control and Dynamic Voltage and Frequency Scaling (DVFS)
2.4.2 PVT sensor
2.5 Clocks
2.5.1 Overview of clocks
2.5.2 Juno r2 SoC and V2M‑Juno r2 motherboard clocks
2.5.3 IOFPGA clocks
2.6 Resets
2.6.1 Reset push buttons
2.6.2 Reset architecture
2.6.3 Reset sequence
2.7 Thin Links
2.7.1 Overview of Thin Links master and slave interfaces
2.7.2 Thin Links master interface
2.7.3 Thin Links slave interface in non‑coherent mode
2.7.4 Thin Links slave interface in coherent mode
2.8 IOFPGA
2.9 HDLCD interface
2.10 Interrupts
2.11 USB 2.0 interface
2.12 SMC 10/100 Ethernet interface
2.13 UART interface
2.14 PCI Express system
2.14.1 Overview of PCI Express system
2.14.2 PCI Express expansion slots
2.14.3 SATA 2.0 ports
2.14.4 Gigabit Ethernet port
2.15 Keyboard and mouse interface
2.16 Additional user key entry
2.17 Debug and trace
3 Configuration
3.1 Overview of the V2M‑Juno r2 motherboard configuration system
3.2 Configuration process and operating modes
3.2.1 Transitions between operating modes
3.2.2 Powerup and configuration sequence
3.2.3 Powerdown sequence
3.2.4 Sleep‑state sequence
3.2.5 Wake‑up sequence
3.3 Configuration files
3.3.1 Overview of configuration files and microSD card directory structure
3.3.2 config.txt generic motherboard configuration file
3.3.3 Contents of the MB directory
3.3.4 Contents of the SITE1 directory
3.3.5 Contents of the SITE2 directory
3.3.6 Contents of the SOFTWARE directory
3.4 Configuration switches
3.4.1 Use of configuration switches
3.4.2 Remote UART configuration
3.5 Use of reset push buttons
3.5.1 Use of ON/OFF/Soft Reset button
3.5.2 Use of Hardware Reset button
3.6 Command-line interface
3.6.1 Overview of the V2M‑Juno r2 motherboard MCC command-line interface
3.6.2 Overview of the LogicTile daughterboard command-line interface
3.6.3 MCC main command menu
3.6.4 MCC debug menu
3.6.5 EEPROM menu
4 Programmers Model
4.1 About this programmers model
4.2 V2M‑Juno r2 motherboard memory maps
4.2.1 Juno r2 SoC top‑level application and SMC interface memory maps
4.2.2 IOFPGA system peripherals memory map
4.2.3 DDR3L memory map
4.2.4 Additional Juno r2 SoC memory maps
4.3 APB system registers
4.3.1 APB system register summary
4.3.2 SYS_ID Register
4.3.3 SYS_SW Register
4.3.4 SYS_LED Register
4.3.5 SYS_100HZ Register
4.3.6 SYS_FLAG Registers
4.3.7 SYS_CFGSW Register
4.3.8 SYS_24MHZ Register
4.3.9 SYS_MISC Register
4.3.10 SYS_PCIE_CNTL Register
4.3.11 SYS_PCIE_GBE Register
4.3.12 SYS_PROC_ID0 Register
4.3.13 SYS_PROC_ID1 Register
4.3.14 SYS_FAN_SPEED Register
4.3.15 SP810_CTRL Register
4.4 APB system configuration registers
4.4.1 APB system configuration register summary
4.4.2 SYS_CFGDATA Register
4.4.3 SYS_CFGCTRL Register
4.4.4 SYS_CFGSTAT Register
4.5 APB energy meter registers
4.5.1 APB energy register summary
4.5.2 SYS_I_SYS Register
4.5.3 SYS_I_A72 Register
4.5.4 SYS_I_A53 Register
4.5.5 SYS_I_GPU Register
4.5.6 SYS_V_SYS Register
4.5.7 SYS_V_A72 Register
4.5.8 SYS_V_A53 Register
4.5.9 SYS_V_GPU Register
4.5.10 SYS_POW_SYS Register
4.5.11 SYS_POW_A72 Register
4.5.12 SYS_POW_A53 Register
4.5.13 SYS_POW_GPU Register
4.5.14 SYS_ENM_SYS Register
4.5.15 SYS_ENM_A72 Register
4.5.16 SYS_ENM_A53 Register
4.5.17 SYS_ENM_GPU Register
A Signal Descriptions
A.1 Debug connectors
A.1.1 P-JTAG connector
A.1.2 Trace connectors
A.2 Configuration 10Mbps Ethernet and dual‑USB connector
A.3 PCI Express Gigabit Ethernet and dual‑USB connector
A.4 SMC 10/100 Ethernet connector
A.5 Configuration USB connector
A.6 Header connectors
A.7 Keyboard and Mouse Interface (KMI) connector
A.8 HDMI connectors
A.9 PCI Express expansion slots
A.9.1 PCI Express ×4 connectors, one-lane slot 0 and slot 1
A.9.2 PCI Express ×8 connector, four-lane slot 2
A.9.3 PCI Express ×16 connector, four-lane slot 3
A.10 SATA 2.0 connectors
A.11 Dual‑UART connector
A.12 Secure keyboard and user push buttons connector
A.13 ATX power connector
B Specifications
B.1 Electrical specification
C Revisions
C.1 Revisions

Release Information

Document History
Issue Date Confidentiality Change
0200-00 16 November 2015 Non-Confidential First issue of TRM
0200-01 15 July 2016 Non-Confidential Second issue of TRM
0200-02 10 January 2017 Non-Confidential Third issue of TRM
0200-03 10 April 2017 Non-Confidential Fourth issue of TRM

Non-Confidential Proprietary Notice

This document is protected by copyright and other related rights and the practice or implementation of the information contained in this document may be protected by one or more patents or pending patent applications. No part of this document may be reproduced in any form by any means without the express prior written permission of ARM. No license, express or implied, by estoppel or otherwise to any intellectual property rights is granted by this document unless specifically stated.

Your access to the information in this document is conditional upon your acceptance that you will not use or permit others to use the information for the purposes of determining whether implementations infringe any third party patents.

THIS DOCUMENT IS PROVIDED “AS IS”. ARM PROVIDES NO REPRESENTATIONS AND NO WARRANTIES, EXPRESS, IMPLIED OR STATUTORY, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY, SATISFACTORY QUALITY, NON-INFRINGEMENT OR FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO THE DOCUMENT. For the avoidance of doubt, ARM makes no representation with respect to, and has undertaken no analysis to identify or understand the scope and content of, third party patents, copyrights, trade secrets, or other rights.

This document may include technical inaccuracies or typographical errors.

TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT WILL ARM BE LIABLE FOR ANY DAMAGES, INCLUDING WITHOUT LIMITATION ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES, HOWEVER CAUSED AND REGARDLESS OF THE THEORY OF LIABILITY, ARISING OUT OF ANY USE OF THIS DOCUMENT, EVEN IF ARM HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

This document consists solely of commercial items. You shall be responsible for ensuring that any use, duplication or disclosure of this document complies fully with any relevant export laws and regulations to assure that this document or any portion thereof is not exported, directly or indirectly, in violation of such export laws. Use of the word “partner” in reference to ARM’s customers is not intended to create or refer to any partnership relationship with any other company. ARM may make changes to this document at any time and without notice.

If any of the provisions contained in these terms conflict with any of the provisions of any signed written agreement covering this document with ARM, then the signed written agreement prevails over and supersedes the conflicting provisions of these terms. This document may be translated into other languages for convenience, and you agree that if there is any conflict between the English version of this document and any translation, the terms of the English version of the Agreement shall prevail.

Words and logos marked with ® or ™ are registered trademarks or trademarks of ARM Limited or its affiliates in the EU and/or elsewhere. All rights reserved. Other brands and names mentioned in this document may be the trademarks of their respective owners. Please follow ARM’s trademark usage guidelines at http://www.arm.com/about/trademark-usage-guidelines.php

Copyright © 2015–2017, ARM Limited or its affiliates. All rights reserved.

ARM Limited. Company 02557590 registered in England.

110 Fulbourn Road, Cambridge, England CB1 9NJ.

LES-PRE-20349

Confidentiality Status

This document is Non-Confidential. The right to use, copy and disclose this document may be subject to license restrictions in accordance with the terms of the agreement entered into by ARM and the party that ARM delivered this document to.

Unrestricted Access is an ARM internal classification.

Product Status

The information in this document is Final, that is for a developed product.

Web Address

Conformance Notices

Federal Communications Commission Notice

This device is test equipment and consequently is exempt from part 15 of the FCC Rules under section 15.103 (c).

CE Declaration of Conformity

To view this graphic, your browser must support the SVG format. Either install a browser with native support, or install an appropriate plugin such as Adobe SVG Viewer.

The system should be powered down when not in use.

It is recommended that ESD precautions be taken when handling Versatile™ Express boards.

The motherboard generates, uses, and can radiate radio frequency energy and may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off or on, you are encouraged to try to correct the interference by one or more of the following measures:

  • Ensure attached cables do not lie across the target board
  • Reorient the receiving antenna
  • Increase the distance between the equipment and the receiver
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
  • Consult the dealer or an experienced radio/TV technician for help

Note:

It is recommended that wherever possible shielded interface cables be used.
Non-ConfidentialPDF file icon PDF versionARM 100114_0200_03_en
Copyright © 2015–2017 ARM Limited or its affiliates. All rights reserved.