AMBA-PV Extensions to TLM 2.0 Developer Guide

Table of Contents

About this book
Intended audience
Using this book
Typographical conventions
Additional reading
Feedback on this product
Feedback on content
1. Introduction
1.1. About the AMBA-PV extensions
2. AMBA-PV Extension
2.1. Introduction
2.2. Attributes and methods
2.2.1. Class definition
2.2.2. Constructors, copying and addressing
2.2.3. Default values and modifiability of attributes
2.2.4. Burst length attribute
2.2.5. Burst size attribute
2.2.6. Burst type attribute
2.2.7. ID attribute
2.2.8. Privileged attribute
2.2.9. Non-secure attribute
2.2.10. Exclusive attribute
2.2.11. Locked attribute
2.2.12. Bufferable attribute
2.2.13. Modifiable/cacheable attribute
2.2.14. Read allocate attribute
2.2.15. Write allocate attribute
2.2.16. Read other allocate attribute
2.2.17. Write other allocate attribute
2.2.18. Quality of Service (QoS) attribute
2.2.19. Region attribute
2.2.20. Domain attribute
2.2.21. Snoop attribute
2.2.22. Bar attribute
2.2.23. DVM messages
2.2.24. Response attribute
2.2.25. ACE response attributes PassDirty and IsShared
2.2.26. ACE snoop response attributes DataTransfer, Error and WasUnique
2.2.27. Response array attribute
2.2.28. Data organization
2.2.29. Direct memory interface
2.2.30. Debug transport interface
2.3. AMBA signal mapping
2.4. Mapping for AMBA buses
2.5. Basic transactions
2.5.1. Fixed burst example
2.5.2. Incremental burst example
2.5.3. Wrapped burst example
2.5.4. Unaligned burst example
3. AMBA-PV Classes
3.1. Class description
3.1.1. AMBA-PV extension
3.1.2. Core interfaces
3.1.3. User layer
3.1.4. Sockets
3.1.5. ACE sockets
3.1.6. Bridges
3.1.7. Memory
3.1.8. Exclusive monitor
3.1.9. Bus decoder
3.1.10. Protocol checker
3.1.11. Signaling
3.1.12. User and transport layers
3.2. Class summary
3.2.1. Additional classes for virtual platforms
3.2.2. Additional classes for side-band signals
4. Example Systems
4.1. Configuring the examples
4.2. Bridge example
4.2.1. Building and running the example
4.3. Debug example
4.3.1. Building and running the example
4.4. DMA example
4.4.1. Building and running the example
4.5. Exclusive example
4.5.1. Building and running the example
5. How to Create AMBA-PV Compliant Models
5.1. How to create an AMBA-PV master
5.2. How to create an AMBA-PV slave
5.3. How to create an AMBA-PV interconnect
5.4. How to create an AMBA-PV ACE master
5.5. How to create an AMBA-PV ACE slave
6. AMBA-PV Protocol Checker
6.1. Introduction
6.1.1. Disabling recommended checks
6.1.2. Selecting AMBA protocol checks
6.2. Checks description
6.2.1. Architecture checks
6.2.2. Extension checks
6.2.3. Address checks
6.2.4. Data checks
6.2.5. Response checks
6.2.6. Exclusive access checks
6.2.7. Cacheability checks

Proprietary Notice

Words and logos marked with or are registered trademarks or trademarks of ARM in the EU and other countries, except as otherwise stated below in this proprietary notice. Other brands and names mentioned herein may be the trademarks of their respective owners.

Neither the whole nor any part of the information contained in, or the product described in, this document may be adapted or reproduced in any material form except with the prior written permission of the copyright holder.

The product described in this document is subject to continuous developments and improvements. All particulars of the product and its use contained in this document are given by ARM in good faith. However, all warranties implied or expressed, including but not limited to implied warranties of merchantability, or fitness for purpose, are excluded.

This document is intended only to assist the reader in the use of the product. ARM shall not be liable for any loss or damage arising from the use of any information in this document, or any error or omission in such information, or any incorrect use of the product.

Where the term ARM is used it means “ARM or any of its subsidiaries as appropriate”.

Confidentiality Status

This document is Non-Confidential. The right to use, copy and disclose this document may be subject to license restrictions in accordance with the terms of the agreement entered into by ARM and the party that ARM delivered this document to.

Product Status

The information in this document is final, that is for a developed product.

Revision History
Revision A28 February 2009New document based on AMBA-PV header files.
Revision B30 April 2009Update to fix defects.
Revision C30 September 2009Split AMBA-PV documentation into Developer Guide and Reference Manual. Added documentation for basic transactions, example systems and the creation of AMBA-PV compliant models.
Revision D31 March 2010Added documentation for the AMBA-PV protocol checker. Added description of AMBA-PV extension attributes and methods.
Revision E30 November 2011Documented changes to support the AMBA4 buses AXI4, ACE and DVM.
Revision F31 May 2012Update for v7.1.
Revision G31 December 2012Release for v8.0.
Revision H30 November 2013Update for v8.3.
Revision I31 May 2014Update for v8.4.
Copyright © 2009-2014 ARM. All rights reserved.ARM DUI 0455I